比特棋牌游戏

最新公告

专业生产快速卷帘门、快速门、快速堆积门、pvc透明软门帘、硬质快速门的开发、设计与生产、销售于一体企业。

当前位置:

比特棋牌游戏>>行业新闻>>「快速门厂家」硬质快速门维修及保养

「快速门厂家」硬质快速门维修及保养

作者:盘锦龙盛快速门制造有限公司   发布时间:2019/8/2 16:26:21

快速门厂家硬质快速门维修保养

 

1、经常检查硬质快速门及确认电源的电压是否符合要求,电压应为380V±10%(三相四线)。冷库设施长期不必时,应截断冷库的总电源,并确保冷库设施不受潮、不被灰埃等其它物质污染。

 

Frequently check the hard fast door and confirm whether the voltage of the power supply meets the requirement. The voltage should be 380V + 10% (three-phase four-wire). When cold storage facilities are unnecessary for a long time, the total power supply of the cold storage should be cut off and the facilities of the cold storage should be protected from dampness, dust and other substances.

 

2、冷库的门的铰链、拉手、门锁应根据实际情况定期添加润滑油。


The hinges, handles and locks of cold storage doors should be regularly lubricated according to the actual situation.

 

3、冷库设施的电器设施检修应有由电工或懂得用电知识的人员来操作,任何检修都必须切断电源,以确保安全。

 

比特棋牌游戏 Electrical equipment maintenance of cold storage facilities should be operated by electricians or people who know how to use electricity。 Any maintenance must be cut off to ensure safety。


4、制冷机在运转过程中应避免振动,振动除了增加机械磨损外还会导致机组上连接管松动或断裂。机器在运转过程中若发明噪声异常,应停机检查,排除后再运行。制冷压缩机组的保护功能均已事先设定好,无须调整。


Vibration should be avoided during the operation of refrigerators. Vibration not only increases mechanical wear, but also causes loosening or fracture of connecting pipes on the unit. If abnormal noise is found in the running process of the machine, it should be stopped and checked, and then run after eliminating it. The protection functions of refrigeration compressor units have been set in advance, and need not be adjusted.


快速门厂家硬质快速门维修保养





5、定期检查制冷机组的各连接管、阀件上的连接管是否牢靠,「硬质快速门」,是否有制冷剂渗漏(一般渗漏的地方会发现油迹)。检漏非常实用的方法是:用海绵或软布沾上 洗涤剂,揉搓起沫,然后均匀涂在要检漏的地方,观察数分钟。若渗漏会有气泡发现。在渗漏的地方做上记号,然后做紧固或气焊处理(由专科制冷工作人员进行检 修操作)


Check regularly whether the connecting pipes on the connecting pipes and valves of refrigeration units are reliable, whether the "hard fast door" has refrigerant leakage (oil stains can be found where the leakage occurs). The most practical method of leak detection is to use sponge or soft cloth to dip in detergent, rub and foam, then evenly apply it to the leak detection area and observe for several minutes. Bubbles will be found if leakage occurs. Mark the leak area and then tighten or gas weld it (it is operated by a specialist refrigeration worker)


6、冷库设施的上面(顶板)不应堆放杂物,否则冷库的库板会变形而影响保温机能,并维持冷库周围通道畅通无阻,只有确保散热良好,制冷才能良好。安放 冷库的位置应维持干燥、清洁、无易燃易爆物品、确保没有任何安全隐患。蒸发器前不得堆放物品(预留一定的空隙),以免影响制冷效果。


The top (roof) of the cold storage facilities should not be stacked with debris。 Otherwise, the cold storage panels will be deformed and affect the thermal insulation function, and keep the passages around the cold storage unobstructed。 Only by ensuring good heat dissipation, can the refrigeration be good。 The location of the cold storage should be kept dry, clean, free of flammable and explosive materials, and ensure that there are no potential safety hazards。 The evaporator must not stack items (reserve certain space) in order to avoid affecting the refrigeration effect。


7、如因空气湿度 过大、化霜间隔时间长、库温设定不正常,所有这些都会导致库内蒸发器上霜层增厚,库温不降。这时就应进行化霜(除霜)处理。并及时观察,等霜层消失立即停 止化霜。稍等片刻后再启动设施。


If the air humidity is too high, the defrosting interval is too long, and the storage temperature is not set properly, all of these will lead to the thickening of the frost layer on the evaporator in the reservoir, and the storage temperature will not decrease. At this time, defrosting (defrosting) treatment should be carried out. And timely observation, such as the disappearance of frost immediately stop defrosting. Wait a moment before starting the facility.

 

8、冷库设施的库内温度、温差等参数,这些都应根据冷库的实际情况而设定,不可任意改变参数。冷库出厂时已根据用户要求而定制,要了解冷库的技术参数后再进行控制器上各项参数的设定。


The temperature, temperature difference and other parameters in the cold storage facilities should be set according to the actual situation of the cold storage, and the parameters should not be changed arbitrarily。 When the cold storage is out of the factory, it is customized according to the user's requirements。 The technical parameters of the cold storage should be known before setting the parameters on the controller。

 

9、定期检查电源电压是否正常(三相四线),检查电源总闸的保护功能是否正常有效。

 

Regularly check whether the power supply voltage is normal (three-phase four-wire), check whether the protection function of the power supply main gate is normal and effective。


快速门厂家硬质快速门维修保养


www。xlssm。cn

联系方式

公司:盘锦龙盛快速门制造有限公司

联系人:艾经理

手机:18248288962

座机:4006080090

QQ:1543064614

联系人:艾经理手机:18248288962座机:4006080090QQ:1543064614

版权所有:盘锦龙盛快速门制造有限公司

秒速时时彩 秒速时时彩 秒速时时彩官网 大发棋牌官网 比特棋牌官网 大发棋牌游戏 大发棋牌app 大发棋牌 比特棋牌官网 比特棋牌游戏